Powerflex Multi-Channel Amplifiers

670

Spec Sheet

All Spec Sheets

All Manuals

All Line Art

All Brochures

General Specifications Power Output Rated Per Channel, Two Channels Driven 70V: 300 Watts RMS 140V (Mono Bridged, 1 Channel: 600 Watts RMS Rated Per Channel, Six Channels Driven 70V: 200 Watts RMS 140V (Mono Bridged, 3 channels): 400 Watts RMS Input Impedance 10K ohm balanced, 37K ohm unbalanced High Pass Filter 80Hz, 12dB/octave, internally selectable THD <0.5% (20Hz - 20KHz 200W 6-Channels Driven) IMD <0.2% (SMPTE 60Hz/7KHz 4:1) Hum and Noise < -100dB from full output (A-weighted) Full Power Input Sensitivity 1.4V RMS (5.1dBu) Frequency Response ±0.5dB (20Hz-20kHz, full power) Voltage Gain 50X (34.0dB) Crosstalk < -75dB (20Hz - 1KHz) Signal Present Signal Sensitivity 14mV RMS (-34.9dBu) Power Requirement 110-125VAC, 220 - 250VAC, 50/60Hz Typical Idle Current 120V: 0.9A 240V: 0.5A Current with Typical Audio Program Material (6 Channels Driven) 120V: 10A 240V: 5A Connections Input: Eurobloc Output: Screw Terminal Indicators Green signal-present LED and red clipping LED. Yellow "thermal"LED, Red "protect"LED Cooling Forced Air, Thermal Sensitive 2-Speed Fan Front Inlet/Rear Outlet Dimensions 19”L x 5.25”H x 16.5”D Construction All-Steel Chassis, Extruded Aluminum Front Panel Weight 47 lbs. net, 54 lbs. shipping Specification conditions are: 120VAC mains at 60Hz, 25° C *Power Output (Maximum Average Power, 0.1% THD, 1KHz)

Architect Specifications 670 The power amplifier shall be a multichannel unit consisting of six independent channels. Each amplifier shall be able to deliver 200 watts at 70 volts, or or when pairs of channels are bridged, 400 watts at 140 volts. Each individual channel shall be able to drive 70 volt distributed audio lines without the use of an external transformer. When channels are paired, the paired channels shall be able to drive 140V distributed audio lines without the use of external transformers. The amplifier shall have a gain of 34.0dB (50x) and an input sensitivity of 1.40 Volts RMS for full rated output. Frequency response shall be 20Hz to 20kHz +/- 0.5dB. Hum and noise shall be at least 100dB below full output (A-weighted) and SMPTE intermodulation distortion shall be less than 0.2%. Total Harmonic Distortion (20Hz - 20KHz) shall be less than 0.5%. Each amplifier channel shall be supplied with an input attenuator located on the rear panel input module. Each pair of inputs shall have a bypassable high pass filter of 12dB/octave at 80Hz, a switch to select independent or parallel channel mode and a switch to select normal 70V or bridge 140V mode. There shall be an input ground switch located on the input module to select chassis or floating ground operation. The inputs shall be active balanced design, with an impedance of 10K ohm accessible with euroblock connectors. The outputs shall be terminated with a screw terminal connector. Individual channel indicators for protect, thermal overload, clip and signal present shall be LEDs located on the front panel. Cooling shall be supplied by a temperature sensitive two-speed fan drawing air from the front of the unit and exiting through the rear. The unit shall be powered from 110 - 125V AC, 220 - 250V AC, 50/60Hz. Dimensions of the unit shall be 19”L X 5.25”H X 16.5”D. The chassis shall be constructed from 16 gauge steel with an aluminum face panel and weigh 47lbs. The unit shall be the Powerflex-670, 70 Volt four channel power amplifier manufactured by Ashly Audio, Inc.

top

Home

Email-Product Support

Email-Service

Email-Sales