|
|
| PE-800/1200/1800/2400/3000/3800 |
| Spec Sheet | All Spec Sheets | All Manuals | All Line Art | All Brochures |
|
|
| General Specifications Power Output: See Power Rating Chart Signal to Noise (20 Hz-20 kHz, unweighted): 800: >98dB 1200: >105dB 1800: >108dB 2400: >110dB 3000: >111dB 3800: >112 dB Output Circuitry: 800: Bipolar, Class AB 1200: Bipolar, Class AB 1800: Bipolar, Class H 2400: Bipolar, Class H 3000: Bipolar, Class H 3800: Bipolar, Class H Power Requirements (1/8 Power Pink Noise @ 4 Ohm): 800: 420W 1200: 640W 1800: 611W 2400: 790W 3000: 1010W 3800: 1220W Current Requirements-Both Channels Driven typ = 1/8 output, pink noise
All Models: Voltage Gain: 26dB, 32dB or 1.5V sensitivity (selectable) Distortion (SMPTE, typical) - 8 ohm load, 10dB below rated power:<0.01% Distortion (THD+N, typical) - 8 ohm load, 10dB below rated power, 20Hz - 10kHz: <0.01% Frequency Response: 20Hz - 20kHz, +/- 0.15 dB Damping Factor - 8 ohm load, <1kHz: > 400 Input Impedance: 20k Ohm, balanced Maximum Input Level: +21 dBu Cooling: Temperature dependent speed-controlled axial fan, front to back air flow Control Network: onboard, compatible with standard 100 MB Ethernet hardware Front Panel Indicators: Per channel: Clip, -6 dB, -12 dB, -18 dB, Temp, Output current. Overall: power, standby, protect, bridged mono, parallel mono, communications Attenuators: 1 per channel: front panel, software, offset and remote Input Connectors, each channel: XLR female/TRS, Euroblock, XLR male (looping) Output connectors-Models 800 and 1200, each channel: Speakon, screw terminals Output connectors-Models 1800, 2400, 3000 and 3800, each channel: Speakon Amplifier Protection: inrush current limitation, temperature monitoring heat-sinks, output DC protection, power transistor SOA protection, output over-current protection, mains fuses protection Load Protection: Adjustable clip limiter Dimensions: 19"W x 3.5"H x 15.5"D (483mmW x 88.9mmH x 394mmD) Weight: Net; 22 to 24lbs., 10 to 10.9kg Shipping; 27 to 29 lbs., 12.3 to 13.2 kg |
Architect Specifications The power amplifiers shall consist of six separate models (800, 1200, 1800, 2400, 3000, and 3800), being of two channels, and shall deliver a minimum power ranging from 200 to 1100 watts RMS per channel into 8 ohm loads and ranging from 400 to 1900 watts RMS per channel into 4 ohms depending on the model being used. When switched into Bridged-Mono mode, the amplifier in use shall deliver a range from 800 to 3800 watts RMS into 8 ohms. All amplifiers shall have the ability for input attenuation, channel mute, channel polarity, input level, output voltage, output current, clipping, temperature, and power on/off be controlled or monitored through the standard, built-in Ethernet port using Proteane Software™. The amplifiers shall have the capability to replace the input module with either a 32 bit/96kHz, Proteane DSP module featuring both analog and digital (AES3) inputs, two additional processed output channels and extensive digital signal processing or the PNE-C2 CobraNet module. Dimensions of the amplifiers shall be 19”W x 3.5”H x 15.5”D, with a weight range of 22 to 24 pounds. The amplifiers shall utilize a state-of-the-art, efficient, two-stage high speed switched mode power supply. Cooling shall be accomplished by the use of a temperature sensitive variable speed fan with front to back airflow. The amplifier shall have a selectable input gain of 26dB, 32dB or 1.4V. Frequency response shall be 20 Hz - 20 kHz, +/- 0.15 dB. Hum and noise shall range fro >98dB to 112dB below full output (20Hz to 20KHz A-weighted) and SMPTE intermodulation distortion shall be <.01% (8 ohm load, 10dB below rated power). Total Harmonic Distortion (20Hz - 20KHz at 8 ohms) shall be <.01% (8 ohm load, 10dB below rated power, 20Hz-10 kHz). Each amplifier channel shall be supplied with a calibrated stepped input attenuator located on the front panel with the capability of the attenuators to be disabled. Each pair of inputs shall have a selectable, bypassable high pass filter of 12dB/octave at 30Hz and 50Hz, a switch to select stereo or mono mode and a switch to select dual or bridge mode. There shall be an input ground switch located on the rear panel to select chassis or floating ground operation and a selectable clip limiter with off, slow, and fast settings. The inputs shall be active balanced design, with an impedance of 20K ohm with a maximum input level of +21dBu. Input connections shall be XLR-1/4” Neutrik combo connectors and 6-pin Euroblock. XLR male connectors shall be provided for looping to additional amplifiers. Output connectors shall be locking Neutrik Speakon. Models 800 and 1200 shall have a 4 position screw terminal strip with safety cover as an additional output. The amplifiers shall have front panel indicators for power, standby, protect, bridged mono, parallel mono, and data communications. Each channel shall have signal indicators for clip, -6 dB, -12 dB, -18 dB levels, temp, output current. The amplifier shall have built in protection for inrush current, temperature, output DC, SOA of power transistors, output over-current and mains power. The amplifiers shall be capable of operation by means of its own built-in power supply connected to 110 - 125VAC, 220 - 250VAC, 50/60Hz. The amplifier shall be covered under a full limited warranty of not less than five years. The amplifier shall be a PE-Series model, manufactured by Ashly Audio, Inc. of Rochester, New York. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
| top | Home | Email-Product Support | Email-Service | Email-Sales |