Mixers

MX-206 Mic Mixer

Spec Sheet

All Spec Sheets

All Manuals

All Line Art

All Brochures

General Specifications THD at +20 dBu, 20Hz-20KHz, input switch at -40dB <0.05% IMD (SMPTE) at +20dBu, input switch at -40dB <0.02% HUM & NOISE (20Hz-20KHz , input switch at -60dB) Equivalent input hum and noise <-127dBu Residual output noise, TRS outputs, all levels at minimum <-100dBu Residual output noise, XLR outputs <-90dBu Master Level at nominal, all Ch. Level controls at min <-84dBu Master Level and one Ch. Level at nom <-80dBuIMUM VOLTAGE GAIN (±2dB) Mic Input to Master Output, 600 ohm load <-84dB Aux In to Master Output <-34dB Frequency Response - 20Hz-20Khz +0/-0.5dB Crosstalk - between any inputs or outputs 20Hz-20KHz <-60dB INDICATORS VU METERS - Two 6-segment LED meters 0VU = +4dBu PEAK INDICATORS Peak Clip indicator on each input channel and left and right outputs, illuminates 3dB below clipping PHANTOM POWER +48 VDC applied to all Mic Inputs, switchable on front panel. Maximum total current draw = 80mA. Maximum single channel current draw = 14mA. Gradual power-up and down to eliminate"pops". SHIPPING WEIGHT 13 lbs. Maximum POWER REQUIREMENTS 100-240 Volts, 50-60 Hz, 30 watts DIMENSIONS: 19" wide x 1.75" high x 8.0" deep. Unless otherwise stated, specification conditions are: 150 ohm source, Input set at "-40", all other controls set at nominal.

Architect Specifications MX-206 The unit shall be a six input stereo microphone mixer with TRS stereo outputs as well as a transformer-isolated +24 dBm , 600 ohm balanced XLR mono output. There shall be +48 volts of phantom power available for condenser microphones, with gradual power-up and down of this phantom power to eliminate any transient spikes. Total voltage gain measured from each microphone input to the Master Output shall be a minimum of 84dB. Each of the six microphone channels shall have 40dB of adjustable gain via a front panel 3 position slide switch. Each input shall also have a 20dB pad switch on the rear of the unit, making a total of 60dB of possible gain/attenuation. Each channel shall have a continuously variable pan control. There shall be a peak Clip LED indicator on each input channel which shall illuminate when the input is 3dB below true clipping, and another Clip indicator on the output of the mixer which shall illuminate when the output is within 3dB of actual clipping. Two 5-segment LED meters must be provided to monitor the mixer output, calibrated for 0 VU to equal +4 dbu. There shall be a separate stereo aux input with front panel level control, having rear panel connection via RCA phono jacks. There shall also be a separate stereo aux output available on the rear panel with access via RCA phono jacks. Distortion shall be less than 0.02 %, Total Harmonic Distortion at +20dBu (20Hz to 20kHz) and less than 0.05% Intermodulation Distortion (SMPTE) at +20 dBu (input switch at -40dB). Hum and Noise shall be less than -100dBu residual output noise when all levels are set at minimum. Frequency Response shall be +0/-.5dB, 20 Hz-20 kHz. Crosstalk of the unit shall be less than -60dB when measuring adjacent inputs or input to output at 20kHz. Dimensions of the model shall be 19" wide x 1.75" high x 8.0" deep. The mixer shall be made in America, with a 13 pound shipping weight. The mixer shall be the model MX-206, manufactured by Ashly Audio, Inc. of Webster, New York. No other unit shall be acceptable unless data submitted from an independent test laboratory verifies that the above specifications are met.

top

Home

Email-Product Support

Email-Service

Email-Sales